Search Results

Conventionally, sound insulation materials have been applied to control interior noise above 500 Hz, and damping materials to control interior noise below 500 Hz. In this paper, the noise control component for vehicle panels, which consists of damping material and sound insulation material, is investigated by using a two-degrees-of-freedom system. The investigation shows that sound insulation material can be effective in reducing interior noise below 500 Hz if its stiffness is reduced. This stiffness depends not only on the spring of the material itself but also on its pneumatic spring which is determined by air-flow resistance. This paper concludes with applications of techniques to reduce interior noise below 500 Hz by improving sound insulation materials.

As a means of effectively incorporating the concept of “life cycle” for reducing the environmental impact of the automobile, we carried out a life cycle inventory study on a part-by-part basis. The targets of our study are the fuel tanks that are made of different materials and manufacturing processes. One is made of steel, and the other is made of plastic, both perform identical functions. Our evaluation study encompasses the period from the manufacturing of the main materials until the disposal of the tanks. The evaluation items consist of the amount of energy consumed and the emissions (of CO2, NOx, SOx, and PM) that are released into the atmosphere. The results show that the plastic tank poses a greater burden in terms of the amount of energy consumed and the CO2 and NOx emitted.

This paper analyzes the vibration of open-top cars known as lateral shake. The characteristics of the phenomenon were identified by means of road tests and a test method called the shake test was devised to reproduce these characteristics in order that the respective roles of the suspension, body and engine could be determined. On the basis of the analysis findings, a simple but practical simulation model was realized and used to investigate various methods of reducing lateral shake. The simulations indicated that although changing the natural frequency of the suspension has little effect, increasing the natural torsional frequency of the body and/or utilizing the engine as a dynamic damper results in a significant improvement. Further experiments conclusively demonstrated that by optimizing the body structure in accordance with FEM analysis results and optimizing the spring constant of the engine mounts, the level of lateral shake can be halved.

The behavior of spray injections to turbulent duct flows from a slit injector for direct-injection gasoline engines was investigated using a combination of large eddy simulation (LES) and Lagrangian discrete droplet model (DDM). As a result, diffusion of droplets in stronger turbulent flows was observed at a later stage of the injection. Moreover, we compared calculation and experimental results by generating a pseudo-particle image from the calculation result.

Automobile production technology has been transferred in the order of "automobile assembly technology", "automotive parts manufacturing technology" and "production preparation technology". Transfer of our "automobile assembly technology" has already been nearly 100% completed and, as the manufacture of local parts is promoted and our experiences to undergo model changes are widened, the transfer of "automotive parts manufacturing technology" and "production preparation technology" is making a steady progress. The most critical point that makes the technical transfer difficult is the small automobile markets in developing countries where it is impossible to acquire a sufficient production volume which permits satisfactorily low cost. Various measures to secure a sufficient production volume such as exports and complementation within regions have been taken so far, but any remarkable effect has not been achieved.

The main operations for the manufacturing of auto parts are the cutting of the flange and the stamping. In order to perform accurate fatigue calculation it is necessary to have the material properties for each point of the structure. Usually, only the fatigue curve obtained on the flat sheet with polished edges is used because it represents the basic metal behaviour. The real edge quality decreases the fatigue limit while the hardening induced by the stamping increases it. To take these effects into account allows a better fatigue calculation of the structural part.

The characteristic of In-Cylinder gas motion of a multivalve engine is compared with a single intake valve engine, which have been predicted by a three-dimensional numerical simulation and flow visualization. The measured intake valve outlet velocity from helical and straight port was adopted as the boundary conditions. The computer graphics technique has been utilized to express the predicted numerical results as moving picture like visualized flow. This flow pattern was compared with the actual flow pattern visualized with metaldehyde as the tracer using the bottom viewed engine, which showed good agreement. The prediction for the multivalve engine showed that the swirl velocity is rapidly reduced by interaction between the flows from the two port, but the turbulence kinetic energy is similar to that in the engines with a single intake valve with helical port.

In contrast to the sensory inspection conventionally performed on the firing bench during final assembly, a technology in which quality inspections are distributed throughout the engine assembly line by using an electric motor to drive the engine, has been developed. Through this process, combustion conditions can be quantitatively tested by component, and leak test conditions can be optimized. Consequently, defects can be detected and their causes identified at an early stage of assembly, thus accelerating the feedback of information to the appropriate process. The result, a level of product quality that is higher than through the conventional means.

In continuous annealing, accelerated cooling methods have recently found practical application in addition to conventional gas jet cooling or water jet quenching method. Moderate cooling rate of gas jet cooling or accelerated cooling makes it possible to utilize new high-strength steels with excellent properties. The faster cooling rate deteriorates ductility of steels. These newly developed steels are improved rephosphorized steels with high r̄-value and high bake hardenability, dual phase steels with superior ductility, Ti-stabilized high-strength steels with very high r̄-value, grain boundary hardening steels employing low temperature annealing, and unique ultra high-strength steels. This paper describes properties and process factors of these steels, and their applications to automotive.

The authors developed a high-reliability low-cost gold-plated connector for automobiles. The connector is covered with three plated layers, nickel, palladium-nickel alloy, and gold. The three-layer plating helps to reduce the required thickness of gold. This paper describes the reasons why palladium-nickel plating was adopted and compares the corrosion resistance, oxidation resistance and wear resistance of three-layer-plated materials with those of conventional gold-plated materials. In addition, the characterisitics of three-layer-plated connectors were compared with those of conventional gold-plated connectors. It was found that the reliability of three-layer-plated connectors was as high as that of conventional gold-plated connectors.

Carburizing heat treatment is one of the automobile component manufacturing steps, which consumes a large amount of energy. Raising the carburizing temperature can shorten the carburizing time and save the energy, but involves the risks of grain coarsening and attendant property deterioration. The authors have clarified the precipitation behavior of aluminum nitride (A1N) in the automobile gear manufacturing process and the optimum precipitation of A1N in as-rolled steel bars to prevent the grain coarsening. Through the application of the controlled rolling technique to ensure the optimum precipitation of A1N in continuously cast steel of uniform chemical composition, the authors have substantially saved energy while maintaining high quality, and developed a high-temperature carburizing steel expected to minimize and stabilize quenching strains.

Engine friction reduction is an effective means to improve fuel consumption. Fluid friction reduction of main bearing is examined for engine friction reduction in cold condition. As one of the examinations, it was focused on low temperature of lubricating oil in the early stage during engine cold start. In hydrodynamic lubrication, the oil film temperature is maintained by balance between heat generation and heat transfer. The heat generation is generated by shear of lubricating oil. The factors of the heat transfer, the following elements are considered as follows, A) The heat transfer to a crank shaft, B) The heat transfer to a bearing, C) The heat transfer by convection. If the heat generation is constant, oil film temperature is increased by reduction of heat transfer. It is considered that the reduction of oil leakage and reduction of the heat transfer by convection is equivalent.

Improvement of material characteristic values, adjustment of forming conditions as well as introduction of new forming technics are necessary to promote wide application of aluminum alloy sheets into automotive parts. 5000 series and 6000 series aluminum alloy sheets are concerned about the relationship between material characteristic values and fundamental forming ability required to apply them to automobile body parts as well as the effect of lubricant on their formability. The hardening parameters, n values, of them are larger than those of cold-rolled steel sheets. However, the r values and the local elongations are extremely small. The improvement of stretch formability owing to increase of n value is smaller than that of the steel sheets. Inferior deep drawability of the aluminum alloy sheets is due to low fracture resistance force caused by low r value.

In order to achieve higher assembly accuracy for automotive body, increased body rigidity, and decreased stamping and assembly costs in car body manufacturing, a new method of sheet metal stamping has been developed, in which several blanks of different strength and thickness are integrated using CO2 laser-welding. The stamping formability of the laser-welded blank is limited compared with that of the conventional single blank. It is very difficult to predict the exact decrease in formability for different positions of the weld line and for different matching of materials. Because experimental estimations were indispensable for stamping die designers to evaluate formability at the stage of planning dies, many man-hours were spent conducting actual experiments.

In this paper the fatigue life of welded steel sheet structures is predicted by using FE-Fatigue, which is one of fatigue analysis software tools on the market, and these predicted results are evaluated by reference to corresponding experimental results. Also, we try to predict these structures by using two fatigue life prediction theories established by the JSAE fatigue and reliability committee to compare prediction results. It was confirmed that spot welds fatigue life predictions agree qualitatively with corresponding experimental results and arc welds fatigue life predictions are in good agreement with corresponding experimental results in cases where the SN curve database is modified appropriately.

Extremely formable cold sheet steel with an ultra-high Lankford value of more than 2.5 and an n value of more than 0.27 has been developed. This steel is obtained due to the following factors; using extremely pure IF (Interstitial free) steel, immediate rapid cooling upon completion of rolling in the hot rolling process, a high reduction in the cold rolling process, and a high soaking temperature in the continuous annealing process. This steel sheet shows excellent deep drawability and stretch formability compared with conventional steel sheet (former IF steel and low carbon aluminum-killed steel) as a result of evaluating the limiting drawing ratio and limiting dome height, respectively. This excellent formability is also shown by the model forming tests for simulating the actual stamping of an oilpan and a side-panel. Furthermore, this steel shows the same spot-weldability as that of former IF steel, and zinc phosphatability similar to that of low carbon aluminum-killed steel.

Previous studies and recent practical aerodynamic evaluations have shown that aerodynamic drag of passenger vehicles with “ground simulation” with moving ground and rotating wheels may increase in some cases and decrease in other cases relative to the fixed ground and stationary wheel conditions. Accordingly, the effects of the ground simulation on the aerodynamic drag should be deeply understood for further drag reduction. Although the previous studies demonstrated what is changed by the ground simulation, the reason for the change has not been fully understood. In this article, the effects of wheels and wheel houses attachment and those by the ground simulation with ground movement and wheel rotation on the aerodynamic drag were investigated by quantification of the underfloor flow that plays a crucially important role on the formation of vortical structure around vehicles.

Certain dimensional factors and a method for evaluating dimensional errors have been developed to improve the service life of the Rzeppa universal joint. The Rzeppa joint Spalling life is extended by disposition of the balls on a constant velocity plane under loading conditions which include proper determination of the offsets of the ball grooves and the windows of the cage. The ball center containment ranges, which consist of the grooves of both inner and outer races, can be affected by dimensional miscalculation of components. Moreover, the extent of scatter in the ball center containment ranges has a remarkable effect on the Rzeppa joint service life.

To reduse crosswind sensitivity, the yaw moment should be decreased under both transient and steady conditions. The transient condition is when a vehicle comes out immediately from a tunnel into a crosswind while the steady condition is when driving straight along the coastline. After studying the pressure distribution and the flow pattern around the body, we have reached the ideal air flow at the front-side corner that reduces the yaw moment under both conditions. And we have devised an entirely new method to achieve this better air flow. The method uses an internal flow generated by a pressure difference in the flow feeld to create a jet effect and by using only a duct for internal flow to control the outside air flow. It is done without any change to the exterior styling, except at the flow exit. We call it “Aero Slit”. This “Aero Slit” is effective only under crosswind conditions, and does not increase aerodynamic drag when a crosswind is not blowing.

A new partial strengthening method, TIG (Tungsten Inert Gas) remelting process, for automobile aluminum alloy castings is described. The preferable operating variables to strengthen, and metallurgical-mechanical properties of remelted alloys formed under selected conditions have been investigated. As a result, the mechanical properties such as strength and toughness, and thermal crack resistance of the remelted alloys were improved markedly due to the effects of microstructure refining and cast defects decrement by remelting. So, the application studies for automobile parts to meet the characteristics of this process have been carried out. Consequently, TIG remelting process has been practically used as an available strengthening method for the portion between valve ports of high performance diesel engine cylinder head.